Improved current mode biquadratic shadow universal filter
Abstract
In this paper, an improved single-input-multiple-output (SIMO) current-mode biquadratic shadow universal filter (SUF) is realized using two new variants of second-generation current conveyors (CCIIs), namely current conveyor cascaded transconductance amplifier (CCCTA) and extra-X current controlled conveyor transconductance amplifier (EX-CCCTA). The low pass and the band pass outputs of a non-shadow universal filter (NSUF), consisting of CCCTA, are utilized through two amplifiers' feedback paths using one EX-CCCTA to realize the proposed SUF. It is resistorless and uses two grounded capacitors only. All the five standard responses of SUF, such as low pass (LP), high pass (HP), band pass (BP), band-reject (BR), and all pass (AP), are obtained through the proposed circuit simultaneously. The important achievement of SUF over the NSUF is the ease of orthogonal tuning of the pole frequency (wo) and quality factor (Qo) with the bias current of CCCTA and EX-CCCTA. It is suitable for full cascadability because of proper input and output impedances. Moreover, it eases the integrated circuit implementation because of all grounded capacitors and no resistor. It does not possess any component matching constraints and consumes only 3.73mW power. The theoretical results have been validated through 180nm technology in Cadence Virtuoso.
Keywords
Full Text:
PDFReferences
W. Tangsrirat, “Single-input three-output elec-tronically tunable universal current-mode filter using current follower transconductance ampli-fiers,” AEU-Int. J. Electron. Commun., vol. 65, n0. 10, pp. 783-787, Oct. 2011, https:doi.org/10.1016/j.aeue.2011.01.002.
C. Wnag, J. Xu, A. U. Keskin, S. Du, and Q. Zhang, “A new current-mode current-controlled SIMO type universal filter,” AEU-Int. J. Electron. Commun., vol. 65, n0. 3, pp. 231-234, Mar. 2011,
https:doi.org/10.1016/j.aeue.2010.02.010.
D. V. Kamat, P. V. A. Mohan, and K. G. Prabhu, “Novel first-order and second-order current-mode filters using multiple-output operational transconductance amplifiers,” Circuits Systems and Signal Processing, vol. 29, pp. 553-576, Mar. 2010,
https://doi.org/10.1007/s00034-010-9163-y.
M. A. Ibrahim, S. Minaei, and H. A. Kuntman, “22.5 MHz current-mode KHN-biquad using dif-ferential voltage current conveyor and ground-ed passive elements,” AEU-Int. J. Electron. Commun., vol. 59, no. 5, pp. 311-318, Jul. 2005, https://doi.org/10.1016/j.aeue.20o4.11.027.
Y. Lakys, and A. Fabre, “Shadow filters-new family of second order filters,” Electronics Let-ters, vol. 46, no. 4, pp. 276-277, Feb. 2010, https://doi.org/10.1049/el.2010.3249.
Y. Lakys, and A. Fabre, “Shadow filter generali-zation to nth class,” Electronics Letters, vol. 46, no. 14, pp. 985-986, Jul. 2010, https://doi.org/10.1049/el.2010.0452.
V. Biolkova, D. A. Biolek, “Shadow filters for or-thogonal modification of characteristic fre-quency and bandwidth,” Electronics Letters, vol. 46, no. 12, pp. 830-831, Jun. 2010.
S. V. Singh, R. S. Tomar, and D. S. Chauhan, “Single CFTA based current-mode universal bi-quad filter,” The Journal of Engineering Re-search, vol. 13, no. 2, pp. 172-186, May 2016, https://doi.org/10.24200/tjer.vol13iss2pp172-186.
N. Herencsar, J. Koton, and K. Vrba, “Single CCTA-based universal biquadratic filters em-ploying minimum components,” International Journal of Computer and Electrical Engineering, vol. 1, no.3, pp. 307-310, Aug. 2009.
S. Minaei, and M. A. Ibrahim, “A mixed-mode KHN-biquad using DVCC and grounded passive elementssuitable for direct cascading,” Interna-tional Journal of Circuit Theory and Applica-tions, vol. 37, pp. 793-810, https://doi.org/10.1002/cta.493.
A. Qadir, and T. Altaf, “Current mode canonic OTA-C universal filter with single input and multiple outputs,” In: Proceedings of Interna-tional Conference on Electronic Computer Technology (ICECT’ 10), pp. 32-34, Jun. 2010, https://doi.org/10.1109/ICECTECH.2010.5479995.
J. Satansup, and W. Tangsrirat, “Single-input five-output electronically tunable current-mode biquad consisting of only ZC-CFTAs and grounded capacitors,” Radioengineering, vol. 20, no. 3, pp. 650-656, Sep. 2011.
D. Biolek, V. Biolkova, Z. Kolka, and J. Bajer, “Single-input multi-output resistorless current-mode Biquad,” In: Proceedings of IEEE Europe-an Conference on Circuit Theory and Design, pp. 225-228, Oct. 2009, https://doi.org/10.1109/ECCTD.2009.5274928.
R. Senani, V. K. Singh, A.K. Singh, D.R. Bhaskar, “Novel electronically controllable current-mode universal biquad filter,” IEICE Electron Express 1, vol. 1, no. 14, pp. 410-415, Oct. 2004, https://doi.org/10.1587/elex.1.410.
W. Tangrirat, T. Pukkalanun, and O. Channum-sin, “Single VDGA-based dual-mode multifunc-tion biquadratic filter and quadrature sinusoidal oscillator,” Informacije MIDEM, vol. 50, no. 2, pp. 125-136, 2020,
https://doi.org/10.33180/InfMIDEM2020.205.
M. I. A. Albrni, F. Mohammed, N. Herencsar, J. Sampe, and S. H. M. Ali, “Novel electroniacally tunable biquadratic mixed mode universal filter
capable of operating in MISO and SIMO config-urations,” Informacije MIDEM, vol. 50, no. 3, pp. 189-203, 2020,
https://doi.org/10.33180/InfMIDEM2020.304
E. Yuce, “Current-mode electronically tunable biquadratic filters consisting of only CCCIs and grounded capacitors,” Microelectronics Journal, vol. 40, no. 12, pp. 1719-1725, Dec. 2009, https://doi.org/10.1016j.mejo.2009.09.002.
A. Kumar, B. Chaturvedi, “Novel CMOS dual-X current conveyor transconductance amplifier realization with current-mode multifunction fil-ter and quadrature oscillator,” Circuits Systems and Signal Processing, vol. 37, pp. 2250-2277, Oct. 2017,
https://doi.org/10.1007/s00034-017-0680-9.
M. Kumngern, “A new current-mode universal filter with single-input five-output using trans-linear current conveyors,” Australian Journal of Eectrical and Electronics Engineering, vol. 9, no. 2, pp. 177-184, Sep. 2015, https://doi.org/10.1080/1448837X.2012.11464322.
B. Singh, A. K. Singh, and R. Senani, “New uni-versal current-mode biquad using only three ZC-CFTAs,” Radioengineering, vol. 21, no. 1, pp. 273-280, Apr. 2012.
M. Kumngern, P. Phasukkit, S. Junnapiya, F. Khateb, and S. Tugjitkusolmun, “ECCCII-based current-mode universal filter with orthogonal control of wO and Q,” Radioengineering, vol. 23, no. 2, pp. 687-696, Jun. 2014.
T. S. Arora, M. Gupta, S. Gupta, “Current mode universal filter employing operational transcon-ductance amplifier and third generation current conveyor,” In: IEEE International Conference on Power Electronics, Intelligent Control and En-ergy Systems (ICPEICES), IEEE, pp. 1-4, Feb. 2017,
https://doi.org/10.1109/ICPEICES.2016.7853305.
A. Abaci, and E. Yuce, “A new DVCC+ based second-order current mode universal filter con-sisting of only grounded capacitors,” Journal of Circuits Systems and Computers, vol. 26, no.9, pp. 1750130, Feb. 2017,
https://doi.org/10.1142/S0218126617501304.
M. A. Albrni, M. Faseehuddin, J. Sampe, and S. H. M. Ali, “Novel dual mode multifunction filter employing highly versatile VD-DXCC,” Infor-macije MIDEM, vol. 49, no. 3, pp. 169-176, 2019, https://doi.org/10.33180/InfMIDEM2019.305.
T. Praveen, “OFC based high output impedance current mode SIMO universal biquadratic fil-ter,” In: International Conference on Multimedia Signal Processing and Communication Tech-nologies (IMPACT), IEEE, pp. 134-136, Feb. 2012,
https://doi.org/10.1109?MSPCT.2011.6150456
R. Arslanalp, E. Yuce, and T. A. Tola, “Two lossy integrator loop based current-mode electroni-cally tunable universal filter employing only grounded capacitors,” Microelectronics Journal, vol. 59, pp. 1-9, Jan. 2017, https://doi.org/10.1016/j.mejo.2016.11.005.
D. Prasad, D. R. Bhaskar, and M. Srivastava, “Universal current-mode biquad filter using a VDTA,” Circuits and Systems, vol. 4, pp. 29-33, Jan. 2013,
https://dx.doi.org/10.4236/cs.2013.41006.
M. Faseehuddin, J. Sampe, S. Shireen, S. H. M. Ali, “Lossy and lossless inductance simulators and universal filters employing a new versatile active block,” Informacije MIDEM, vol. 48, no. 2, pp. 97-113, 2018.
N. Pandey, A. Sayal, R. Choudhary, and R. Pandey, “Design of CDTA and VDTA based fre-quency agile filters,” Advances in Electronics, vol. 2014, pp. 1-14, Dec. 2014, https://doi.org/10.1155/2014/176243.
N. Pandey, R. Pandey, R. Choudhary, A. Sayal, and M. Tripathi, “Realization of CDTA based frequency agile filters,” IEEE International Con-ference on Signal Processing, Computing and Control, pp. 1-8, Nov. 2013, https://doi.org/10.1109/ISPCC.2013.6663403.
M. Atasoyu, H. Kuntman, B. Metin, N. Her-encsar, and O. Cicekoglu, “Design of current-mode class 1 frequency agile filter employing CDTAs,” European Conference on Circuit Theo-ry and Design, pp. 1-4, Oct. 2015, https://doi.org/10.1109/ECCTD.2015.7300066.
D. Nand, and N. Pandey, “New configuration for OFCC-based CM SIMO filter and its application as shadow filter and its application as shadow filter,” Arabian Journal for Science and Engi-neering, vol. 43, no. 6, pp. 3011-3022, June. 2018,
https://doi.org/10.1007/s13369-017-3058-1.
A. Yesil, and F. Kacar, “Band-pass filter with high quality factor based on current amplifier,” AEU-Int. J. Electron. Commun., vol. 75, pp. 63-69, May 2017,
https://doi.org/10.1016/j.aeue.2017.03.007.
M. Atasoyu, B. Metin, H. Kuntman, and N. Her-encsar, “New current-mode class 1 frequency-agile filter for multi-protocol GPS application,” Elektronica ir Elektrotechnika, vol. 21, no. 5, pp. 35-39, May 2015,https://doi.org/10.5755/j01.eee.21.5.13323.
D. Singh, and S. K. Paul, “Realization of current mode universal shadow filter,” AEU-Int. J. Elec-tron. Commun., vol. 117, pp. 1-16, Apr. 2020,
https://doi.org/10.1016/j.aeue.2020.153088
F. Khateb, W. Jaikla, T. Kulej, M. Kumngern, and D. Kubanek, “Shadow filters based on DDCC,” IET Circuits Devices Syst., vol. 11, pp. 631-637, Oct. 2017, https://doi.org/10.1049/iet-cds.2016.0522.
S. C. Roy, “Shadow filters: a new family of elec-tronically tunable filters,” IETE J. Edu., vol. 51, pp. 75-78, Sep. 2014, https://doi.org/10.1080/09747338.2010.10876070.
M. T. Abuelma’atti, N. R. Almutairi, “New cur-rent-feedback operational amplifier based shadow filters,” Analog Integr. Circ. Sig. Pro-cess., vol. 86, pp. 471-480, Jan. 2016, https://doi.org/10.1007/s10470-016-0691-7.
M. T. Abuelma’atti, N. Almutairi, “New voltage-mode bandpass shadow filters,” In: 13th Interna-tional multi-conference on systems, signals & devices, pp. 412-415, May 2016,
https://doi.org/10.1109/SSD.2016.7473695.
M. T. Abuelma’atti, N. Almutairi, “New CFOA-based shadow bandpass filters,” In: 15th Interna-tional conference on electronics information, and communications, Sep. 2016, https://doi.org/10.1109/ELINFOCOM.2016.7562969.
R. Anurag, R. Pandey, N. Pandey, M. Singh, and M. Jain, “OTRA based shadow filters,” Annual IEEE India Conference, Mar. 2016, https://doi.org/10.1109/INDICON.2015.7443524.
P. Huaihongthong, A. Chaichana, P. Suwanjan, S. Siripongdee, W. Sunthonkanokpong, P. Supavarasuwat, W. Jaikla, and F. Khateb, “Sin-gle-input multiple-output voltage-mode shad-ow filter based on VDDDAs,” AEU-Int. J. Elec-tron. Commun., vol. 103, pp. 13-23, May 2019, https://doi.org/10.1016/j.aeue.2019.02.013.
A. Yesil, F. Kacar, and S. Minaei, “Electronically controllable bandpass filters with high quality factor and reduced capacitor value: an addi-tional approach,” AEU-Int. J. Electron. Com-mun., vol. 70, pp. 936-943, Jul. 2016, https://doi.org/10.1016/j.aeue.2016.04.009.
T. Thosdeekoraphat, S. Summart, C. Saetiaw, S. Santalunai, and C. Thogsopa, “CCCTAs based current-mode quadrature oscillator with high output impedances,” International Journal of Electronics and Electrical Engineering, vol. 1, no. 1, pp. 52-56, Jan. 2013.
D. Agrawal, and S. Maheshwari, “Current mode filters with reduced complexity using a single EX-CCCII,” AEU-Int. J. Electron. Commun., vol. 80, pp. 86-93, Oct. 2017,
https://doi.org/10.1016/j.aeue.2017.06.025.
DOI: https://doi.org/10.33180/InfMIDEM2022.106
Refbacks
- There are currently no refbacks.
Copyright (c) 2022 Divya Singh, Sajal K. Paul
This work is licensed under a Creative Commons Attribution 4.0 International License.